Phone Icon0208 953 1211       Email Iconinfo@conro.com

 x 
Cart empty

HumiSeal 1A33 Urethane - 1 Liter Container

HumiSeal® 1A33 is a 1 Litre single component, polyurethane conformal coating, suitable for general printed circuit board applications. HumiSeal® 1A33 contains no free isocyanates and fluoresces under UV light for inspection purposes. HumiSeal® 1A33 coating is MIL-I-46058C qualified, IPC-CC-830 and RoHS Directive 2002/95/EC compliant and recognized under UL File Number E105698.
Manufacturer: Humiseal
Description

Properties of HumiSeal® 1A33 1 Litre

Density, per ASTM D1475 0.95 ± 0.02 g/cm³
Solids Content, % by weight per Fed-Std-141, Meth. 4044 44 ± 2 %
Viscosity, per Fed-Std-141, Meth. 4287 180 ± 20 centipoise VOC 531 grams/litre Recommended Coating Thickness 25 - 75 microns Drying Time to Handle per Fed-Std-141, Meth. 4061 15 minutes
Optional Curing Conditions to Reach Optimum Properties 30 days at RT
30 hours @ 76°C
20 hours @ 88°C Recommended Thinner (dipping, brushing) HumiSeal® Thinner 503
Recommended Thinner (spraying) HumiSeal® Thinner 521, 521EU Recommended Stripper HumiSeal® Stripper 1063
Shelf Life at Room Temperature, DOM 24 months Thermal Shock, 50 cycles per MIL-I-46058C -65°C to 125°C Coefficient of Thermal Expansion - TMA 193 ppm/°C Glass Transition Temperature - DSC 26°C
Modulus - DMA 27.2 MPa
Flammability, per UL 94 V-0
Dielectric Withstand Voltage, per MIL-I-46058C >1500 volts Dielectric Breakdown Voltage, per ASTM D149 7500 volts Dielectric Constant, at 1MHz and 25°C per ASTM D150-98 3.6
Dissipation Factor, at 1MHz and 25°C per ASTM D150-98 0.03
Insulation Resistance, per MIL-I-46058C 2.0 x 1014 ohms (200TΩ) Moisture Insulation Resistance, per MIL-I-46058C 1.6 x 1010 ohms (16GΩ) CTI, PLC per UL746E @ 600 volts 0
Fungus Resistance, per ASTM G21 Passes

Application of HumiSeal® 1A33

Cleanliness of the substrate is of extreme importance for the successful application of a conformal coating. Surfaces must be free of moisture, dirt, wax, grease, flux residues and all other contaminants. Contamination under the coating could cause problems that may lead to assembly failures.

Dipping

Depending on the complexity, density and configuration of components on the assembly, it may be necessary to reduce the viscosity of HumiSeal® 1A33 with HumiSeal® Thinner 503 in order to obtain a uniform film. Once optimum viscosity is determined, a controlled rate of immersion and withdrawal (5-15 cm/min) will further ensure even deposition of the coating and ultimately a uniform film. During the application, evaporation of solvent causes an increase in viscosity that should be adjusted by adding small amounts of HumiSeal® Thinner 503. Viscosity in the dip tank should be checked regularly, using a simple measuring device such as a Zahn or Ford viscosity cup.

Spraying

HumiSeal® 1A33 can be sprayed using conventional spraying equipment. Spraying should be done in an environment with adequate ventilation so that the vapour and mist are carried away from the operator. The addition of HumiSeal® Thinner 521 or 521EU is necessary to ensure a uniform spray pattern resulting in pinhole- free film. The amount of thinner and spray pressure will depend on the specific type of spray equipment used and operator technique. The recommended ratio of HumiSeal® 1A33 to HumiSeal® Thinner 521 or 521EU is 1:1 by volume; however the ratio may need to be adjusted to obtain a uniform coating.

Brushing

HumiSeal® 1A33 may be applied by brush. Uniformity of the film depends on component density and operator's technique.

Storage

HumiSeal® 1A33 should be stored away from excessive heat or cold, in tightly closed containers. HumiSeal® products may be stored at temperatures of 0 to 35°C. Prior to use, allow the product to equilibrate for 24 hours at a room temperature of 18 to 32°C.

Caution

Application of HumiSeal® Conformal Coatings should be carried out in accordance with local and National Health and Safety regulations.
The solvents in HumiSeal® 1A33 are flammable. Material should not be used in presence of open flame or sparks. Use only in well-ventilated areas to avoid inhalation of vapours or spray. Avoid contact with skin and eyes.

Consult MSDS/SDS prior to use.

envelope

CONTACT US

Conro Electronics Ltd
Unit 7, Orbital 25, Dwight Road, Watford, Hertfordshire
WD18 9DA

delivery van icon

NEXT DAY DELIVERY

We offer next day and Saturday deliveries excluding orders made after 3pm weekdays, weekends and public holidays.


AS 9120B

Conro Electronics Ltd certified to the AS 9120B (Aerospace) standard

Click Here To View Our Certificate

ISO 9001:2015

Conro Electronics Ltd certified to ISO 9001:2015

Click Here To View Our Certificate