Humiseal UV40HV UV Curable Conformal Coating
From £355.85
HumiSeal UV40HV is a single component, high solids, UV curable, acrylated polyurethane conformal coating that has been formulated specifically for dispensing and jetting applications.
Free shipping on orders over £75
Same day dispatch if you place your order before 3.30pm
Manufacturer CofC available at checkout
HumiSeal UV40HV conformal coating is:
- single component
- high solids/high viscosity
- UV curable
- acrylated polyurethane
HumiSeal UV40HV conformal coating has:
- excellent chemical resistance, surface hardness, flexibility, and moisture resistance.
- secondary moisture cure mechanism for curing in the non-UV exposed shadowed areas
- fluoresces under UV light to allow for coating inspection
- can be applied by selective coating equipment.
- IPC-CC-830 and RoHS directive 2015/863/EU
- China Standard GB30981-2020
Application of UV40HV Conformal Coating
Conformal coatings can be successfully applied to substrates that have been cleaned prior to coating and also to substrates assembled with low residue, “no clean” assembly materials. Users should perform adequate testing to confirm compatibility between the conformal coating and their particular assembly materials, process conditions and cleanliness level. Please contact HumiSeal® for additional information.
Spraying
HumiSeal UV40HV can be applied via standard selective coating equipment or by conventional hand spray equipment. The source air used for spraying must be dry (a dry inert gas is highly recommended) to prevent premature curing of the secondary cure mechanism. The spraying should be done with adequate ventilation so that the vapor and mist are carried away from the operator.
Brushing
HumiSeal UV40HV may be applied by brush for rework or touch up only. Brush must be cleaned with solvent promptly after use.
Clean Up
To flush equipment and clean uncured HumiSeal UV40HV, non-alcohol based solvents should be used. HumiSeal Thinner 521 or Thinner 521EU is recommended.
Rework
HumiSeal UV40HV is a highly cross-linked UV cured coating. The cured film has a high degree of environmental and chemical resistance and will be more difficult to remove than traditional conformal coatings. Thermal displacement, mechanical abrasion and, where available, HumiSeal Stripper 1100 are suitable options for rework of HumiSeal UV40HV.
| Density | 1.05 – 1.15 g/cm3 |
| Minimum Solids Content |
95 % |
| Viscosity, per Fed-Std-141, Meth. 4287 | 3,700 +/- 1,300 centipoise |
| Recommended UV Cure* | See curing section below |
| Shelf Life at Room Temperature, DOM | 12 months |
| Recommended Stripper ** | HumiSeal® Stripper 1100 |
| Thermal Shock, 50 cycles per MIL-I-46058C | -65°C to 125°C |
| Glass Transition Temperature - DSC | 45°C |
| Coefficient of Thermal Expansion - TMA | 85 ppm/°C below Tg 197 ppm/°C above Tg |
| Dielectric Withstand Voltage, volts per MIL-I-46058C | >1500 |
| Dielectric Constant, at 1MHz and 25°C per ASTM D150-98 | 2.5 |
| Dissipation Factor, at 1MHz and 25°C per ASTM D150-98 | 0.01 |
| Insulation Resistance, per MIL-I-46058C | 8.0 x 1014 ohms (800TΩ) |
| Moisture Insulation Resistance, per MIL-I-46058C | 4.7 x 1010 ohms (47GΩ) |
| Fungus Resistance, per ASTM G21 | Pass |
-
Humiseal-UV40-HV-TDS.pdf
Size: 208.85 kB
Type: pdf
-
Humiseal-UV40HV-SDS.pdf
Size: 153.26 kB
Type: pdf
Delivery info
Shipment method | Shipment cost |
Click and Collect | FREE |
Next day (orders above £75.00 ex.vat) | FREE |
Next day (orders below £75.00 ex.vat) | £6.99 |
Next day pre 12AM | £17.99 |
Next day pre 10AM | £20.99 |
Saturday AM | £45.00 |
Be the first to review “Humiseal UV40HV UV Curable Conformal Coating”
Related products
Reviews
There are no reviews yet.