Phone Icon0208 953 1211       Email

Cart empty

Surclean Dry Ultrawipes IPA/DI

Ultrawipes are manufactured from a synergistic blend of virgin Polyester and Rayon hydro entangled into a high strength uniform fabric. The material is a premium quality product that has been custom developed to provide the optimum balance of attributes such as high absorbency, toughness, abrasion resistance and freedom from particle generation and abrasive characteristics found in other competing materials that contain wood pulp derived cellulose.
Manufacturer: Surclean

Composition/Information on Ingredients

General description: a mixture of solvent and water for the removal of residues in Electronics

Hazardous ingredients

Name of Ingredient Concentration Risk Phrases

Isopropanol Alcohol - 70% - irritant R37
D.I. Water - remainder - N/A

Hazards Identification

‑Odour: Slight fragrence
‑Appearance: Colourless liquid
‑Contact with skin: Prolonged skin contact will result in defatting of the skin, irritation, and possible
‑Inhalation: Irritating to eyes and respiratory system (836/37. May cause dizziness, confusion, headache or

First aid measures

Contact with skin
‑wash the affected area with plenty of soap and water.
‑afterwards, a suitable moisturising skin cream can be applied.

Contact with eyes
‑If material has got into eyes, wash out immediately with plenty of water for at least 15 minutes.
‑Seek medical attention if any irritation persists.

‑Seek medical attention immediately.

Inhalation and General
‑Remove the patient from source of exposure to fresh air and lie down. Seek medical advice if neccesary. If casualty is unconcious, place into the recovery position. Perform artificial respiration if breathing has stopped. If breathing is difficult, properly trained personnel may assist affected person by administering 100% Oxygen. Keep affected person warm and at rest. Seek prompt medical attention.

Fire fighting measures

Extinguishing Media
-in case of fire use water spray or fog, alcohol resistant foam, dry chemical or C02 (S43), Sand, Dolomite etc.
Special Fire Fighting Procedures
-Do not use water jets. Wear breathing apparatus. Use Water to keep fire exposed containers cool and to disperse vapours. Dike for water control. Cool containers exposed to flames with water until well after the fire is out. Move container from the fire area if it can be done without risk. Use water spray to reduce vapours. For large scale fires in cargo areas, use unmanned hose holder or monitor nozzles if possible. If not, withdraw and let fire bum out. If risk of water pollution occurs, notify appropriate authorities.
Exposure hazards
-None known

Accidental release measures

Immediate actions
-Shut off all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate.

Clean up procedures
-Provide ventilation and confine spill. Do not allow runoff to sewer. Absorb spillage in a suitable inert material such as vermiculite, dry sand or earth and place into appropriate container. Avoid contact with skin or inhalation of spillage, dust or vapour. Clean up personnel should use respiratory and liquid contact safety protection clothing.

Handling and Storage

Usage precautions
-Keep away from sources of ignition. Avoid spilling, skin and eye contact. Ventilate well, avoid breathing vapours. Use approved respirator if air contamination is above accepted level. Wear full protective clothing for aged exposure and/or high concentrations.

Storage Precations
-Low risk flammability/combustibility-keep away from oxidizers, heat and Names. Isolate from other materials. Keep in a cool, dry, ventilated stage and dosed containers. Ground container and transfer equipment to eliminate static sparks risk.

Storage Criteria
-Chemical storage.

Exposure Qntrols and Personnel Protection

Normal good room ventilation should be sufficient. Gloves and eye protection are recommended for prolonged or
repeated exposure.

Protective Equipment

-provide adequate general and local exhaust ventilation.
-No specific recommendation made, but respiratory protection must be used if the general
level exceeds the Occupational Exposure Level (OEL).
Protective Gloves
-Use protective Gloves. Chloroprene, Nitrile or Butyl Rubber Industrial grade Gloves.
Eye protection
-Wear approved safety goggles. Full face shield protecttion preferred.
Other Protection
-Wear appropriate clothing to prevent any possibility of liquid contact and repeated or
prolonged vapour contact.
Hygenic Work routines
-DO NOT SMOKE IN WORK AREA. Wash at the end of each work period and before
food consumption, smoking or using the toilet. Remove any clothing that becomes
contaminated immediately. Do not eat or drink whilst working with this material.

Physical and Chemical Properties

-colourless liquid
-Mild. Alcohol. Sweet.
Solubility Description
-Soluble in water.

Changes of state Value/range unit method
Boiling point/range 88 deg C.
Flash Point 49 deg C. Pensky Martens C.Cup.
Auto ignition temperature 425 deg C.

Explosion hazard

Explosion limits
-lower 3.4 % -upper 18%
Vapour pressure
-58Pa @ 20 deg. C.
-0.826 - 0.892 @ 20 deg. C.
PH Value
-3.1 mPas @ 20 deg. C.

Stability and Reactivity

-Avoid: heat, sparks, moisture and flames.
Materials to avoid
-Bases, Alkalies (Inorganic), Strong Oxidizing agents, Strong Reducing agents
Hazardous Decomposition products
-Material does not decompose up to the specified boiling point. Thereafter in case of fire, material can create Vapours/gases/Fumes of: Carbon Monoxide (CO), Carbon Dioxide (C02).

Toxicological Information

Toxic Dose-LD50
-ingestion: No data is available for oral toxicity. The values of the ingredients are higher than LD50 (oral rat) : 2000mg/kg.
Skin Contact
-Repeated/prolonged contact causes degreasing, irritation and possible dermatitus.
Eye Contact
-Initial eye contact will cause chronic eye irritation. Inhalation -Higher concentrations can cause irritation of the respiratory system, nausea and dizziness.

Ecological Information

-Dissolves in water. Product remaining on surface evaporates within one day. Larger volumes may penetrate soil layer and could contaminate groundwater.
Does not significantly bio-accumulate.
-Material is readily bio-degradable meeting the 10 day window crriterion. Oxidizes rapidly by photochemical reactions in air. This together with its very high flash point means it can be treated as a very low VOC potential material. Integrated environmental half-life is estimated to be 1-< 10 days.
Acute Fish Toxicity
-Practically non toxic. However best practice states material must not be drained.

Disposal Considerations

Disposal methods UK
-Dipose of in accordance with Local Authority requirements.
EEC waste listing class according to (94/3/EG)
-Disposal No. 140303 (Solvents/Solvent blends not containing Halogenated material)
Suggested disposal/recovery meths
Filtration waste should be collected and disposed of by licensed Chemical waste removal Contractors. Specification of minor waste content will be mostly that of the production materials for which the cleaning material was used. To advise the disposal contractor therefore, refer to the production material data source.

Transport Information

Ground Transportation ADR/RID
-ADR/RID Class 3 Alcohols, n.o.s. (Cont. I.P.A.)
-item 31 C
-UN number 1987

Sea Transportation IMDG - Code
-IMGD Classification 3.3 Alcohols, n.o.s. (Cont. I.P.A.)
-page 3303
-UN number 1987
-Packaging class III
-EMS number 3 - 06
-MFAG 305

Air Transportation ICAO-TI and IATA-DGR
-ICAO/IATA Classification 3 Alcohols, n.o.s. (Cont. I.P.A.)
-UN ID number 1987 Packaging instructions - 309 / 60 I
-Packaging Class 111 - 309 / 10 I
-10 / 220 1 (Cargo Aircraft only)

Regulatory Information

EEC Supply Label- X IRRITANT

Risk Phrases
-820/21/22 Harmful by inhalation, in contact with skin/eyes, and if swallowed.
-R37 Irritating to respiratory system.
Safety Phrases
-S-24/25 Avoid contact with skin and eyes.
-S36/37 Wear suitable protective clothing and gloves.
Statutary Instruments
-Chemicals (Hazard Information and Packaging) regulations.
-Control of Substances Hazardous to Health (CoSHH) regulations.
Guidance Notes
-Occupational Exposure Limits HSE publication No. EH40.

Issue date and revision number

Issued on 16/01/2001. Issue revision 01.


This information relates only to the specific material designated and will not be valid for such material used in combination with any other material or in any process. Such information is, to the best of the Manufacturers knowledge and belief, accurate and reliable as of the date shown. However, no warranty, guarantee or representation is made as to its accuracy, reliability or completeness. It is the users sole responsibility to satisfy himself as to the suitability of such information for their particular application.



Conro Electronics Ltd
Unit 7, Orbital 25, Dwight Road, Watford, Hertfordshire
WD18 9DA

delivery van icon


We offer next day and Saturday deliveries excluding orders made after 3pm weekdays, weekends and public holidays.

AS 9120B

Conro Electronics Ltd certified to the AS 9120B (Aerospace) standard

Click Here To View Our Certificate

ISO 9001:2015

Conro Electronics Ltd certified to ISO 9001:2015

Click Here To View Our Certificate